How to Install Your Vertagear RGB LED Upgrade Kit
By Vertagear: Innovating health and comfort with ergonomic chairs. | Published: 2026-10-17
Category: How-to Guides
Step-by-step instructions for installing the RGB LED Upgrade Kit on your Vertagear chair. Learn how to route the strip, connect the controller, and avoid common mistakes.
Quick Answer
Installing the Vertagear RGB LED Upgrade Kit takes about 20 minutes and requires only a Phillips-head screwdriver. The kit attaches to the underside of your chair frame and connects to a small controller box that you mount under the seat. Follow the steps below for a clean, secure installation that avoids pinched wires or loose strips.
What You Need Before You Start
Make sure you have the Vertagear RGB LED Upgrade Kit (sold separately), a Phillips-head screwdriver, and a clean workspace with enough room to tilt your chair on its side. The kit includes the LED strip, a controller box, mounting clips, adhesive pads, and a USB power cable. If you also ordered a custom logo engraving service like the Light Up Your Logo - PL4800 Edition or PL4500 Edition, note that those are laser-engraved logos and do not include the RGB kit; you will need this separate upgrade kit to add lighting to the engraved area.
Check that your chair model supports the kit. The upgrade is designed for most Vertagear S-Line chairs, including the SL5800. If your chair has a solid metal frame without pre-drilled mounting holes, you may need to use the included adhesive pads instead of screws. The kit does not require any wiring modifications to the chair itself.
Common Mistakes to Avoid
The most frequent error is routing the LED strip too tightly around sharp metal edges, which can damage the strip or cause it to detach. Leave a little slack at corners and use the included clips to secure the strip flat against the frame. Another common mistake is plugging the USB cable into the controller before the strip is fully installed; this can make it harder to tuck the cable neatly. Always route and secure the strip first, then connect the power last.
Installation Steps
- Prepare the Chair: Tilt your chair onto its side on a soft surface (like a carpet or towel) to protect the upholstery. Locate the underside of the seat frame where the LED strip will attach. Clean the area with a dry cloth to remove dust or grease. Checkpoint: Make sure the chair is stable and won't roll. If your chair has gas lift adjustment, avoid resting weight on the lever.
- Route the LED Strip: Peel the backing from the adhesive pads on the LED strip and press it along the underside edge of the seat frame, starting from the back center and working toward the front. Use the included mounting clips at every 6-8 inches to secure the strip, especially near corners. Common mistake: Pulling the strip too tight around corners can cause it to lift or break. Leave a small loop at each turn.
- Mount the Controller Box: Attach the controller box to a flat area under the seat using the adhesive pad or screws (if pre-drilled holes are available). Ensure the controller is positioned so the USB port faces outward for easy cable routing. Checkpoint: Do not mount the controller where your legs or the chair mechanism might hit it during use.
- Connect the Strip to the Controller: Plug the LED strip connector into the matching port on the controller. The connector is keyed, so it only fits one way. Push firmly until it clicks into place. Do not force it if it does not align; rotate the connector 180 degrees and try again. Common mistake: Plugging the strip in upside down can reverse the color order or cause one section to stay dark. Double-check alignment before pushing.
- Route the USB Cable and Test: Tuck the USB cable along the chair frame using the included cable clips, keeping it away from moving parts like the tilt mechanism. Plug the USB end into a powered USB port (5V, 1A minimum) on your PC or a wall adapter. Turn on the controller to test the lighting. Checkpoint: If the strip does not light up, unplug the USB, check the connector alignment, and ensure the controller is receiving power. Do not leave the strip partially connected while powered on.
Product Facts
- SL5800: SL5800 | Best Ergonomic RGB Gaming Chair. Ergonomically designed for comfort to prevent chronic back pain. Patent pending ContourMax™ Lumbar contouring your back’s shape and movement, keeping you in a healthy posture and VertaAir™ Seat feature air emission tunnels to provide pressure relief for your sit bones. The SL5800 is a compatible base chair for the RGB LED Upgrade Kit. Its ergonomic features keep you comfortable during long gaming or work sessions, while the added lighting lets you personalize the look without sacrificing support.
