How to Install the RGB LED Upgrade Kit on Your Vertagear Chair

Quick Answer

Installing the RGB LED Bottom Kit on a compatible Vertagear PL4500 or PL4800 chair takes about 20–30 minutes. Unbox all parts, mount the LED strip to the underside of the seat base, connect the power and controller, then pair the wireless remote. The kit is designed as a seamless, wirelessly operated system, so no complex wiring is required. Always disconnect power before you start and test the lights before fully securing the strip.

So you’ve got the Vertagear RGB LED Bottom Kit and you’re ready to light up your setup. Good news: this is one of the simplest upgrades you can make to a compatible chair. The kit is built for the PL4500 and PL4800, and it’s the world’s first wirelessly operated RGB gaming chair system, which means fewer cables and more flexibility.

This guide walks you through the full RGB LED upgrade kit installation process in order. Each step includes a checkpoint or a common mistake so you can avoid the usual pitfalls. Before you begin, confirm your chair model and clear a workspace where you can safely flip the chair upside down.

Before You Start: Compatibility and Tools

The RGB LED Bottom Kit is designed specifically for the Vertagear PL4500 and PL4800 gaming chairs. If you own a different model, the mounting points and fit may not match. Check your chair’s model name on the underside of the seat or on the original packaging. If you’re unsure, measure the mounting area and compare it to the kit’s bracket spacing before you begin.

You won’t need many tools. A Phillips-head screwdriver, a clean microfiber cloth, and a soft surface to rest the chair on are usually enough. If your kit includes adhesive-backed strips, have isopropyl alcohol handy to clean the surface. Avoid using power tools on plastic mounting points, as over-tightening can crack them.

• Common mistake: starting the install without confirming your chair model. The kit fits PL4500 and PL4800 only.
• Checkpoint: lay out all kit components and verify nothing is missing before you flip the chair.

Step 1: Power Down and Prepare the Chair

Unplug your chair from any power source and remove any existing accessories that might get in the way. Tilt the chair onto its side or upside down on a soft, clean surface. This gives you clear access to the underside of the seat base, where the LED strip will mount. If your chair has a plastic base cover, remove it gently and set the screws aside in a small bowl so they don’t roll away.

Take a moment to wipe down the mounting area with a dry or slightly damp cloth. Dust and oil can prevent adhesive from bonding properly. Let the surface dry completely before moving to the next step.

• Common mistake: skipping the cleaning step. Even a thin layer of dust can cause the LED strip to peel off later.
• Checkpoint: the mounting surface should be dry, clean, and free of loose debris.

Step 2: Mount the LED Strip to the Seat Base

Peel the backing from the adhesive on the LED strip and carefully align it along the underside edge of the seat base. Start from one end and press firmly as you work your way around, avoiding sharp bends that could damage the internal circuitry. The strip should sit flush against the surface without overlapping itself. If your kit uses brackets instead of adhesive, line up the screw holes and hand-tighten the screws until snug.

For a cleaner look, route the strip so the connector end points toward where you plan to place the controller. This reduces the chance of excess cable hanging loose. Don’t fully commit to the placement until you’ve done a quick test fit.

• Common mistake: bending the strip at a sharp angle. LED strips can crack if forced around tight corners.
• Checkpoint: the strip should be firmly attached and evenly aligned before you move on.

Step 3: Connect the Controller and Power

Plug the LED strip connector into the controller module. It should click or slide in securely; don’t force it. Next, connect the power cable to the controller and route the cable along the underside of the chair, using the included clips or adhesive tie-downs if provided. Keep the cable away from moving parts like the tilt mechanism or gas lift, as repeated rubbing can wear through the insulation.

If your kit includes a separate power adapter, plug it into a wall outlet now, but leave the chair in a position where you can still see the underside. You’ll want to test the lights before final cable management.

• Common mistake: routing cables through the chair’s swivel or tilt range. Always leave slack and secure cables to fixed parts.
• Checkpoint: the controller should have a solid connection and the power cable should have no tension.

Step 4: Pair the Wireless Remote

The RGB LED Bottom Kit is wirelessly operated, so pairing is straightforward. Turn on the controller if it has a physical switch, then press and hold the pairing button on the remote until the lights flash or respond. Refer to the kit’s manual for the exact pairing sequence, as it may vary slightly. Once paired, cycle through a few colors and effects to confirm the connection is stable.

If the remote doesn’t respond, check the battery orientation and make sure the controller is powered. Move the remote closer to the controller and try again. Interference from other wireless devices is rare but possible, so keep the remote within a few feet during pairing.

• Common mistake: assuming the remote is broken when the controller isn’t powered on. Always check power first.
• Checkpoint: the lights should change color and brightness smoothly when you use the remote.

Step 5: Test, Tidy, and Finalize

With everything connected, test all the lighting modes you plan to use. Check that the strip stays lit when the chair is tilted or swiveled, and that no cables pull tight. Once you’re satisfied, use cable clips or zip ties to secure any loose wiring to the underside of the seat. Trim zip ties flush so they don’t snag on clothing or the floor.

Finally, flip the chair back upright and sit in it to confirm nothing presses into the LED strip or wiring. The underside should be smooth to the touch. If you ever need to remove the kit, peel the strip slowly and use a mild adhesive remover to clean residue.

• Common mistake: leaving cables dangling. They can catch on the base or floor and damage the connectors.
• Checkpoint: all lights work, cables are secure, and the chair sits flat without obstruction.

Installation Steps at a Glance

1. Confirm compatibility: Check that your chair is a PL4500 or PL4800. The RGB LED Bottom Kit is designed for these models only. If you have a different model, the kit may not fit.
2. Power down and prep: Unplug the chair and flip it onto a soft surface. Clean the underside of the seat base. A clean, dry surface ensures the adhesive bonds properly.
3. Mount the LED strip: Peel and press the strip along the underside edge, avoiding sharp bends. Use brackets if provided. Test the fit before fully securing the strip.
4. Connect controller and power: Plug the strip into the controller, then connect power. Route cables away from moving parts. Leave slack so cables don’t pull when the chair tilts.
5. Pair the wireless remote: Turn on the controller and follow the pairing sequence in the manual. Test colors and effects. If pairing fails, check batteries and proximity.
6. Test and tidy: Cycle through lighting modes, secure cables with clips, and trim zip ties. Sit in the chair to check comfort. Ensure no wires press into your legs or the floor.

Product Facts

• RGB LED Bottom Kit: Designed for Vertagear PL4500/PL4800 gaming chairs and is the world’s first wirelessly operated RGB gaming chair kit. Confirms compatibility and explains why pairing is wireless, so you don’t need to route a remote cable.
• SL5800: Ergonomic gaming chair with patent pending ContourMaxTM Lumbar and VertaAirTM Seat air emission tunnels. If you’re considering a new chair alongside the LED kit, the SL5800 offers advanced ergonomic features but does not support the RGB LED Bottom Kit.

Installing the RGB LED Bottom Kit is a straightforward upgrade that adds wireless lighting to your PL4500 or PL4800. Follow the steps in order, and don’t rush the cleaning and cable management. If you want to personalize your chair further, the Light Up Your Logo – PL4800 Edition lets you add a custom laser-engraved logo that works alongside the RGB kit. Enjoy your newly lit setup.